本文へスキップ

SHIBAURA Institute of Technology

Department of Electrical Engineering

Publications

2019
2018
2017
2016
2015
2014
2013
2012
2011
2010
2009

2019

Symposium
  1. Kan Akatsu, "A study of a behavior model which is created by Finite Element Analysis - Characteristics and New utilization -", IEE-Japan Industry Applications Society Conference (JIASC) 3-S14-4, 2019.
International Conference
  1. Taketo Tomioka, Kan Akatsu, "Study of High-speed SRM with Amorphous steel sheet for EV", International Conference on Electrical Machines and Systems 2019 (ICEMS 2019), 2019
Academic meeting
  1. Toshiyuki Suzuki, Keiji Takeda, Kan Akatsu, "Magnets available for the variable magnetic force motors", IEE-Japan Industry Applications Society Conference (JIASC) 4-6, 2019.
  2. Muhammad Lucky Hari Andono, Kan Akatsu, "Investigation on Coil End Effect of an IPMSM to the Output of VR Resolver", IEE-Japan Industry Applications Society Conference (JIASC) 3-53, 2019.
  3. Satoshi Kuramoto, Kan Akatsu, "A design of wireless electric supply antenna for automated guided vehicle (AGV) in 13.56 MHz", IEE-Japan Industry Applications Society Conference (JIASC) 4-4, 2019.
  4. Koichi Koinuma, Kan Akatsu, "A novel self cooling SRM for electric hand tools", IEE-Japan Industry Applications Society Conference (JIASC) 3-80, 2019.
  5. Taketo Tomioka, Kan Akatsu, "Study of High-speed SRM with Amorphous steel sheet for EV", IEE-Japan Industry Applications Society Conference(JIASC) 3-82, 2019.
  6. Tatsuru Tamori, Kan Akatsu, "A method of current mesurement of the bonding wire by using giant magnetic resistive sensor (GMR sensor)", IEE-Japan Industry Applications Society Conference(JIASC) 1-23, 2019.
  7. Naoya Hieda, Kan Akatsu, "A study about the correction of inverse magnetic field in open magnetic circuits", IEE-Japan Industry Applications Society Conference(JIASC) 3-35, 2019.
  8. Kazunari Honda, Kan Akatsu, "A method of operating permanent magnet synchronous motor (PMSM) using the double three-phase inverter", IEE-Japan Industry Applications Society Conference(JIASC) 3-60, 2019.
  9. Rei Kasahara, Kan Akatsu, "A study of driving system in MATRIX motor", IEE-Japan Industry Applications Society Conference (JIASC) Y-118, 2019.
  10. Naoya Kanda, Kan Akatsu, "A design of the high efficiency rectifier for receiving side for 13.56MHz", IEE-Japan Industry Applications Society Conference (JIASC) Y-23, 2019.
  11. Naoya Kawashima, Kan Akatsu, "Direct torque control (DTC) by using flux sensing for PMSM", IEE-Japan Industry Applications Society Conference (JIASC) Y-128, 2019.
  12. Yuzuki Tsuchiya, Kan Akatsu, "Study of SRM using Grain-Oriented Electrical Steel Sheet", IEE-Japan Industry Applications Society Conference (JIASC) Y-104, 2019.
  13. Taichi Nishio, Kan Akatsu, "A method of decreasing torque ripple in PMSM considering the temperature of magnet", IEE-Japan Industry Applications Society Conference (JIASC) Y-125, 2019.
  14. Kano Matsuura, Kan Akatsu, "A motor control method using mechanical learning", IEE-Japan Industry Applications Society Conference (JIASC) Y-139, 2019.
  15. Ryosuke Minegishi, Kan Akatsu, "Expansion of the operating area of flux switching motor (FSM) using variable magnets", IEE-Japan Industry Applications Society Conference (JIASC) Y-101, 2019.
  16. Masanori Watanabe, Kan Akatsu, "A design of high electrical power and high efficiency antenna in 13.56MHz WPT", IEE-Japan Industry Applications Society Conference (JIASC) Y-22, 2019.

ナビゲーション

バナースペース